The essay that was sent to me suggested resetting everything again, this time changing my LED technology from “Wide LED” to “Standard LED”. From what I could decipher, the device I have is not that great for profiling a multi-monitor setup. The swift response I got back from support was an essay on the very technical aspects of colour calibration and the caveats.
![spyder 3 pro review spyder 3 pro review](https://www.ephotozine.com/articles/Datacolor-Spyder-3-Elite-10656/images/spyder3_prodshot2.jpg)
Getting more despondent I email support again. When complete my monitors don’t match in colour temperature. I can now meet the on-screen targets and set the Spyder running. They swiftly suggest running through the application again. Making any lookups of issues you may be facing quite tedious.
SPYDER 3 PRO REVIEW PDF
It makes great reading if you have an hour or so and does stomp on the motto “quick calibration”, alas the PDF is not interactive and you cannot click through to the section from the menus to easily get to the relevant section. Support suggest I read their ebook on colour calibration. I reset my monitor back to factory defaults and try again, no luck. My monitor doesn’t have the option to switch off Dynamic Contrast as it is “greyed out”. Eager to get this sorted and pleased with their customer support I delve into my monitor menus once more. After an exchange of emails, Datacolour suggest I change the Dynamic contrast of my monitor to “off”, they assure me it is an option with my monitor as they looked it up for me. They reply the next morning and say they have not received the screenshot I uploaded to their “ticket” system for help.
SPYDER 3 PRO REVIEW HOW TO
I can’t figure out how to stop this crazy light show I’ve got going on. It seems to randomly switch between the three and it is very off-putting. The profile seems to conflict with the “evening” warm setting that comes on late at night. I decide to contact SpyderX for support… Before I get my reply, the monitor I’m trying to calibrate flicks between the new “colour profile” just created by SpyderX and my old one. It could be that because I could not meet the “brightness target” that things were messed up. It “measures” a whole band of different colours and then presents me with a new preset of how my screen should look. I seem to be miles from the target brightness.Īs I can’t turn it up anymore I carry on. I turn up the brightness to maximum and the values on-screen don’t change. When I use the touch sensor menus, my screens offer to control the brightness.
SPYDER 3 PRO REVIEW SOFTWARE
The SpyderX software tells me to adjust my screen brightness to match the indicators on screen. I am not sure if my SpyderX Pro review is going as well as i hoped. It warns me that the lens cap is on and I should remove it. This is less than ideal and wonder how people with three monitors can connect and profile their furthest monitor, clearly a bit of a drawback to the device! No instructions were given on how to operate the device.
![spyder 3 pro review spyder 3 pro review](https://www.the-digital-picture.com/Images/Review/Datacolor-Spyder4-Elite-Display-Calibration-System.jpg)
My tape solution would have to do for the moment due to the cable being too short. Working with a multiple-monitor set up the screen I chose was my left screen, the one furthest from my computer and not the one I use for my colour work but still exactly the same make and model. The next screen says I should place the Spyder on my screen according to the on-screen location guide. I don’t know if my monitors have such a thing but as I entered the model number in the setup I assume it knows more than I do. Working from home lighting changes all the time, I figured this would be a good idea. I’m looking for a slick experience so switch on “Automatic Room light switching”.
![spyder 3 pro review spyder 3 pro review](https://images-na.ssl-images-amazon.com/images/I/41cn+vLeQoL._UL500_.jpg)
I select “ok” here and fish around for information about “room light switching”. Sypderx pro monitor calibration Rabbit Hole The menus can now be filled out as it seems to recognise the device. My workstation is big and sits way back under the desk. The cable is only 1.5 meters so has reached around a fair distance to get to my monitor and it is a bit of a stretch, it doesn’t quite reach. Annoyingly the only USB I can access is the top-mounted USB on my PC. I am not allowed to fill out the options at this stage as I guess there is something wrong with my USB hub, although the other devices all seem to work. Assuming at this stage that everything is fine I press on with filling out the options. Only there is no sensor listed just a black box with “ok”, I click “ok”.Ī new box pops up (i’m sensing a theme here) and presents me with a selection of options. Clicking “next” on the prompts and another prompt pops up asking me to “select the sensor from the following dialogue”. I plug it into my USB hub and nothing happens. On reaching for the device I notice the cable is 1.5 meters long. Being like any man I just want to get on and use the thing! On clicking “ok” another window popped up asking me to make sure that it is plugged in. The URL seemed like a diversion at this point. Sypderx-pro-monitor calibration notice First Pitfall